- My age:
- I was born in Poland
- What is my hair:
- Long hair
- Figure type:
- My figure type is muscular
- I prefer to drink:
- My favourite drink ale
- My hobbies:
Do you need advice on what products to buy?
Traveling down the road come with its own dangers. Make sure you and your vacation are protected by using the right anti-sway bars. Installing the sway bar is simple to do, but it also depends on location. Keep the sway bar centered to the hitch ball. That was just the first step in installing the sway bar. To find out the rest of the steps just continue to read our article.
It lets you know how to install a sway bar and gives you some adjustment tips. Tip 1 : One of the first things you need to do is get a set of sway bars that fit your trailer.
Proper way to hitch an rv
Not all sway bars are made the same and some do not work with those trailers that have surge brakes. The sway bars work on specific hitches and weight limits only. Tip 2 : Do a fully loaded test drive at normal towing speeds. Monitor your trailer's actions and when you stop, you need to locate the tension screws. Your test drive should tell you which way you need to turn that tension screw. We have given you the first step already, but here is a reminder. Make sure the sway ball is centered on the hitch bar.
What causes sway?
Step two is to attach the handle to the car or tow vehicle. Once that is done use a rag and grease the thre of the handle, so it moves easily for you. Tighten the bolts and attach the bar coupler to the ball. Step four, hold the bracket in place and drill holes through it and the frame. Then use a hammer to drive the rivets through those holes. After that, you should be good to go and ready for your road trip.
You do not have to do both sway bars every time you make an adjustment. Here are some steps to help you install your sway bar correctly and avoid road problems when you are away from home.
Tip 4 : when it is icy, snowing or you are in heavy rain, you need to remove the sway bar. Then when you go to reinstall the sway bars you have to go through the test drive and adjustment process again. This is not a hard action to do perform.
The sway bars should Sway bar hook up with adjustment screws that need a little turn, either way, to make sure you have the right tension on your trailer. To make sure you know which way to turn those screws, you should do a test drive with your tow vehicle and your trailer filled with the same weight you will have on your trip. Travel at the same speeds you would normally travel at to make sure you get the best reading possible. This will increase or decrease the tension on your trailer and make it safer for the road. One of the first things you need to do is take your time. Be patient when making your adjustments.
Nothing is gained by rushing through this procedure. Also, make sure you know which direction you need to turn to increase or decrease the tension. A very important step is to double-check to make sure the sway bar was installed properly. A bad installation will hamper your adjustment process. It will also make your trailer unsafe and you will probably continue to have swaying issues affect your driving.
Do the test drive over and over till you get the adjustment where it should be. Tip 6 : depending on your sway bar de and model type, sometimes all you have to do is turn the handle to add or subtract friction. You turn the handle till you get the right balance of friction for both the tow vehicle and the trailer. This can be a difficult problem to solve because of some models of sway bars naturally make noise.
It is just the nature of the beast. Some experienced RV owners get embarrassed by the noise one brand makes but there is nothing they can do about it. Another cause could be it is just installed too tight.
All you have to do in this situation is just loosen the sway bar a little bit and the noise should be reduced considerably. If the noise comes when you are backing up, you should take the tension off before you do that. A homemade answer is to turn to a little petroleum jelly. Tip 7 : it is best to know the function of your sway bars. All the stiffness does is reduce the amount of the lean your vehicle experiences when it comes face to face with sway sources. You can get what is called a weight distribution sway bar. What this device does is help distribute the weight of your tow vehicle and trailer over all the axles and do it evenly.
Once you attach the bar, your trailer should be stabilized a lot better and should be able to withstand those sway causing elements a lot easier. This type of sway bar comes with a spring system that helps stabilize the trailer and distribute the weight.
Then those hitches that come with their own anti-sway bars are generally made for small tongue trailers. Tip 8 : One of the adjustments you can make, and it will indirectly help the sway bar perform more effectively, is managing your tongue weight.
Make sure your tongue weight remains between 12 and 15 percent and your sway bar should not have as much trouble. Here is one way to hook up your travel trailer when it already has a sway bar attached and in position. Firs tback your tow vehicle into position.
Secondlower the hitch tongue till it is almost at rest on the ball. Thirdinsert weight distribution bars into the receivers on the hitch, pulling them tight on the trailer tongue. Once done, just lower the tongue until it rests on the ball. Finallyjust reconnect the sway bar and you should be ready for the road. One word of caution here. If the dealer already attached the sway bar for you, ask them to give you a list of instructions to follow to attach your tow vehicle to the trailer. Or ask them to show you how it is done.
How can i prevent sway?
The reasoning behind this is that it can be dangerous to attach your trailer to the hitch ball if you do not know what you are doing. If you make the wrong move, you could be seriously injured. Also, each of the different brands of sway bars, especially the weight distribution models, all have their own way of hooking up. What was listed above only works for certain types and is not the procedure for them all. So, make sure you get instructions and a demonstration to help you avoid an injury to yourself.
Before we start here, we will reiterate the above and put a little more emphasis on key parts. Make sure you have the proper instructions for your model of sway bar.
The instructions we put here is just for a limited of models. Then be careful when you do it, trailer tongues and other vehicle parts are heavy and can cause a lot of damage. Here are those instructions for you:. Step oneloosen the sway bar then remove it. Step twounlock the ball latch and lower the tongue jack, getting it in position to lift the tongue. Step threestart using the tongue jack and when the tongue just starts to lift stop and the truck starts to move up from the lack of weight. Step fourremove the distribution weight bars, then lifting the tongue until the tow vehicle can be driven away safely.
One keynote to be wary of, make sure to check the trailer Sway bar hook up first and keep the stabilizing bars retracted until the process is completed. Adjusting and installing your new sway bar is not going to be that difficult. You just need to know what you are doing. Also, let them show you how to adjust the adjustment screws so you know which way to turn to increase or decrease the tension.
Remember, each sway bar is different, and they do not work for every trailer. Know the details of your tow vehicle and trailer and find the right sway bar for both. Also, be careful. These are some risks involved when attaching or unhooking your trailer with a sway bar attached. Share Pin. Travel Trailer Hitch and Sway Bars. Raise your vehicle-make sure to get it high enough off the ground to work safely on it. Now you remove the end links.